Product Categories
Social Media
Home > News > Content
Dry Powder Pressing Mold Does Not Appear Rubber And Shooting Does Not Move The Fault
- Aug 11, 2017 -

Dry Powder Pressing Mold does not appear rubber and shooting does not move the fault
For dry powder to suppress the mold, if it is not the phenomenon of non-rubber, we have to know to see it's plastic film is not the phenomenon of burned, or have foreign objects into our directional valve, then It is carded with a spool to move, or will be for the plastic injection valve to be replaced; or, for Dry Powder Pressing Mold pressure is too low phenomenon, but also to increase the pressure of injection can be.
For Dry Powder Pressing Mold does not appear to the case of plastic injection molding into the temperature is relatively low, this time is to adjust the thermometer for our temperature directly to the requirements of the point can be raised. But adjust the thermometer or can not increase its temperature, it is necessary to check the electric heater and the fuse to see if it is not burned or loose phenomenon, if it has been broken, but also to be replaced in a timely manner of.
For the Dry Powder Pressing Mold, its sol screw rotates, and in terms of its compound, it can not enter the barrel. In general, the back pressure of the sol after its sol is relatively high, it is necessary to adjust or replace the sol backpressure valve when it is damaged or improperly adjusted.
Dry powder to suppress the mold of the shooting table does not move the phenomenon of words, for its shot limit limit stroke switch is concerned, it will be adjusted to hit the block pressure, then the direct adjustment can be; for the shooting table mobile solenoid valve Of the coil is also possible to have burned out or there is a foreign object into the direction of the valve to carry the card to move the spool, then we need to clean its solenoid valve or replace.
When the shot of the Dry Powder Pressing Mold can not move, the speed of the advancement of the shooting table is checked to see if the pressure is not suitable for the adjustment. In addition, the 1/2 board of the Dry Powder Pressing Mold is checked, The valve output voltage is to be checked, to see if it is not normal, if it is not normal, it should be the output of the transistor or relay, etc. to see if it is not already damaged.
 Speaking of Dry Powder Pressing Mold in which the three-dimensional design is concerned, it is actually digital mold technology is an important part of the matter, it is actually in order to achieve the Dry Powder Pressing Mold on the design and manufacturing and testing integration aspects Foundation. Japan's Toyota and its US General Motors and other companies, it is actually will have been achieved on the mold of the three-dimensional design, and will achieve a better application effect.
     In terms of foreign speaking, in the three-dimensional design of Dry Powder Pressing Mold, it is taken in some of the practice is worthy of our reference. In terms of mold three-dimensional design itself, it is in addition to its own to achieve integrated manufacturing, the other one of its advantages, in fact, it is easy to interfere with the inspection, so that is, in fact, can be directly on the movement On the interference analysis, to solve its own two-dimensional design of a difficult problem.
     Dry Powder Pressing Mold which stamping, it is actually simulating the role of CAE, so that in fact, it will be more prominent. On the recent point of view, in fact, it will be with the computer software and hardware on the rapid development of its stamping process CAE simulation technology is actually will directly play an increasingly important role.
     In the United States, Japan, Germany and a series of developed countries, in terms of CAE technology, in fact, it will have become a mold design and manufacturing of the necessary links, so that, in fact, is used to predict the formation of defects, Then, in fact, it will be directly to optimize its stamping process and mold structure.
     In this way, for improving the reliability of the design of the Dry Powder Pressing Mold, and its reduced test time. CAE technology is widely used, in fact, it will greatly reduce the cost of its test mode, so that is, in fact, it will shorten the stamping Dry Powder Pressing Mold on the development cycle, has been directly to ensure that our mold quality An important means.