Product Categories
Social Media
Home > News > Content
A New Technology To Effectively Extend The Life Of Hot Pressing Grouting Mold
- Sep 25, 2017 -

A new technology to effectively extend the life of Hot Pressing Grouting Mold
      The proven powder metallurgy process is widely used in machinery and other industries. The quality and life of Hot Pressing Grouting Mold is an important factor in determining the quality and longevity of powder metallurgy parts. Therefore, it is very important to improve the quality and life of the mold. The use of cryogenic treatment can improve the wear resistance of steel in order to achieve the quality and life of the mold, parts quality and life will be increased.
      Hot Pressing Grouting Mold is usually due to wear and damage caused by parts of the size of the resulting waste. Tool steel in the heat treatment in the metallographic phase will usually leave a lot of austenite, the use of molds prone to organizational changes, resulting in tissue stress, resulting in early damage from the mold, especially when the residual austenite more than 5% of the time, will be obvious Reduce the strength and abrasion resistance of the material.
     In the powder metallurgy industry widely used Gr15 steel as a mold material, but in use with Gr15 steel mold quality and life are low, so the use of cryogenic treatment to improve the wear resistance of steel, and ultimately improve the Hot Pressing Grouting Mold's quality and longevity.
     After a series of experiments, Gr15 steel in the normal heat treatment still remains more austenite, cryogenic treatment is the best way to reduce the austenite residue. When the temperature of the cryogenic treatment is reduced to -140 ° C or less, the amount of retained austenite is substantially stable.
     After the cryogenic treatment, the toughness of the GR15 steel is not changed, but the strength is slightly increased. This is because the cryogenic treatment changes the austenite to the martensite, the organization is more refined and the hardness is enhanced. Therefore, the overall strength of the GR15 steel The quality of the Hot Pressing Grouting Mold has been significantly improved.
     Experiments show that Hot Pressing Grouting Mold reduces the amount of austenite after cryogenic treatment, increases the toughness and strength, which significantly improves the quality and life of the mold, and the economy of the mold is further improved. Cryogenic treatment is a way to promote and use it. On this basis, we will continue to study the effect of a better way to make Hot Pressing Grouting Mold quality and life again.
Under normal circumstances, Hot Pressing Grouting Mold brittle cutting effect, in fact, much better than plastic, and can more easily meet the relevant processing requirements, but for the same material, in the metallographic structure, if it is more Small words, then the better, this point in the industry are more recognized.
       First, Hot Pressing Grouting Mold In the forging equipment, if it is based on the weight of the forging classification, then it is best to use tonnage larger mold or equipment, and in forging before the use of hammer or hammer drill Mold preheating in advance to ensure the good operation of the production process.
       Second, Hot Pressing Grouting Mold in the preparation of the billet powder, the blank at the time of cutting, it is best to carry out cold saw, and according to Hot Pressing Grouting Mold different requirements, in the choice of raw materials, should be selected in accordance with the level , Different materials using different molds, so that the processing will be more accurate.
       Third, Hot Pressing Grouting Mold billet heating, the heating of the blank, it is best to slow to prevent the rapid heating of the way to avoid the phenomenon of burning, and in the heating process, the temperature should not limit the lower limit , If the case of burning, it should be the first to cool it and then forging.
       If you are heating a number of Hot Pressing Grouting Mold, you must ensure that there is a certain clearance between each piece and each piece, and that the parts must be flipped throughout the heating process to ensure that There will be no bonding between each other to ensure that the product processing and use of normal.
       The Hot Pressing Grouting Mold after cutting is still poor in profile and shape, and there is a big difference between the contours made with the pure structure, mainly because the plasticity is severe after the cutting process Of the deformation, and we in the cutting time, the choice of the tool is also more important.
       Because the different tools in the precision, as well as fine cutting high and low speed will have an impact, it is serious will affect the normal use of Hot Pressing Grouting Mold. If the brittle Hot Pressing Grouting Mold material is processed, then the rate of cutting is not significant for roughness.